Dongguan Hanhui Electronics Co., Ltd.

Ganzhou Canhigher Electronics Co., Ltd.

Language

NEWS

Homepage

News

Company News

About the wire harness factory's testing standards for copper wires

Categories:Company News
Author:
Origin:
Time of issue:2021-04-07 14:42
Views:

(Summary description)Copper wire is an integral part of the wire harness. The quality of the copper wire is related to the quality of the wire harness. Therefore, the wire harness manufacturer needs to have a testing standard for the copper wire. So what are such standards?

About the wire harness factory's testing standards for copper wires





About the wire harness factory's testing standards for copper wires

Categories:Company News
Author:
Origin:
Time of issue:2021-04-07 14:42
Views:

Information

Copper wire is an integral part of the wire harness. The quality of the copper wire is related to the quality of the wire harness. Therefore, the wire harness manufacturer needs to have a testing standard for the copper wire. So what are such standards?

1. Appearance inspection

Place the spool full of copper wire on the packing table, hold the white paper in one hand and place it at a position 1 to 2 cm away from the copper wire, and roll the spool of copper wire around with the other hand, and then observe it visually Its appearance has not reached the following standards.

(1) The surface should be lubricated, there should be no messy lines, no oxidation, and no scratches, etc.

(2). The wiring must be even, without stacking and underside, and there must be no staking.

(3) The tension should be moderate, not too loose or too tight.

(4) There should be no dust sticking on the surface after the copper wire is rolled.

2. Detection of wire diameter

The wire diameter should be produced according to national standards. Assuming that the customer has special requirements, it also needs to be strictly controlled according to its requirements. The detailed process is as follows:

(1) First, debug whether the micrometer has returned to zero.

(2) Put the copper wire to be inspected outside the clamping line of the micrometer, and twist the end of the micrometer with appropriate force.

(3) Suppose that after hearing the three beeps of the micrometer, the reading should be checked immediately.

(4) Repeat inspections must be carried out until the readings are the same. The same orientation cannot be detected each time, and the inspections must be carried out in sections.

3. Inspection of elongation

The elongation rate should be checked according to the relevant national standards. Assuming that the customer has special requirements, it should be strictly controlled according to the requirements. The detailed process is as follows:

(1) Turn on the switch of the elongation tester

(2) Check whether the induction clamp on the left of the copper wire is in the original position, and whether the reading flashed on the instrument has been reset to zero. Assuming that the clamp on the left is not in the original location and the reading flashed by the instrument has not been reset to zero, then To immediately press the zero-setting button and the recovery button.

Previous: The difference between OTG data cable and ordinary USB data cable!

Next: The wiring harness processing factory introduces what are the specific interface types of the connecting line

Previous: The difference between OTG data cable and ordinary USB data cable!

Next: The wiring harness processing factory introduces what are the specific interface types of the connecting line

More information

Basic knowledge of data cable [ 2021-05-14 ]

The data cable is used to connect mobile devices and computers to achieve the purpose of data transmission or communication. In layman's terms, it is a channel tool that connects computers and mobile

The fast charging era is coming! Do you understand 120W super flash charging? [ 2021-05-14 ]

Speaking of fast charging, the first reaction in everyone's mind may be "charge for 5 minutes, talk for two hours". This brainwashed sentence has also become "charge for 5 minutes, play for two hours"

iPhone13 may have to cancel the accessories again, things may not be so simple! [ 2021-05-14 ]

Looking back on 2020, the most impressive thing about Apple is that the iPhone 12 series does not come with chargers and earphones. Although Apple is called "environmental protection", from the consum

The difference between OTG data cable and ordinary USB data cable! [ 2021-04-07 ]

The USB data cable has become a common and essential digital accessory in daily life. However, with the rapid development of the mobile phone industry, the OTG cable has gradually entered the public's field of vision. The OTG cable is so similar to the USB cable, so what is the difference between them? The USB data cable is used to connect the mobile phone and the computer. It can access the data such as photos and music in the mobile phone through the computer. At the same time, because the mobile phone has its own memory or expansion card, in a sense, the mobile phone is also another kind of U disk. Of course, it is also an indispensable connection bridge for charging mobile phones, tablets, MP4 and other digital devices.

The key points of data cable purchase you should know! [ 2021-04-07 ]

On major e-commerce platforms, all kinds of data lines are overwhelmed, and people who don't know it will be dazzled. I believe that many people's attitude towards the data cable is: almost, all the same, buy a cheap one. Don't have this idea. Inferior data cables will not only cause damage to the mobile phone, but also infringe on your own safety. So when you buy a data cable, you must not be greedy for petty bargains, and make a mistake and hate forever.